Home › Furnace filters › ML180UHE(K)
Our script found these filter sizes in the Lennox ML180UHE(K) source document's filter table: 14x25x1, 16x25x1, 20x25x1, 24x25x1. This page is pending human review, so check the source excerpt on the page to see which size applies to your cabinet and return.
Auto-extracted · review pending Filter sizes auto-extracted from the manufacturer document.
| Sizes / part numbers found in the source table |
|---|
| 14 X 25 X 1 |
| 16 X 25 X 1 |
| 20 x 25 x 1 |
| 24 x 25 x 1 |
Extracted by script from the linked document. Read the excerpt to see which size applies to which cabinet or return.
General guidance (not from this manual): check monthly and replace 1-in. filters every 1–3 months, or follow the filter maker's guidance and your owner's manual.
Pull the old filter and read the size printed on its frame. Nominal sizes are rounded up: a 15.5 x 24.5 in. filter is sold as 16 x 25.
Your furnace manual lists the filter's dimensions, not its MERV rating. Higher-MERV filters restrict more air. Manufacturers such as Carrier recommend keeping the clean-filter pressure drop under 0.2 in. w.c. (ideally under 0.1). Lennox warns that an over-restrictive filter can trip the high limit in winter and freeze the coil in summer. If you want MERV 11–13, a 4-in. media cabinet is the usual route. Ask an HVAC tech to check static pressure. Nominal sizes are rounded: a filter labeled 16 x 25 x 1 actually measures about 15.5 x 24.5 x 0.75.
Manufacturer document for Lennox ML180UHE(K)
Last checked 2026-10-23. Manufacturers revise documents. If your unit's label disagrees, trust the label.
ENTRY VENT
PIPE vided high-velocity filter is required for the unit to operate
properly. TABLE 1 lists recommended filter sizes. A filter
must be in place any time the unit is operating.
TABLE 1
Furnace Cabinet Filter Size
Width Side Return Bottom Return
SERVICE PLATFORM A - 14-1/2” 16 X 25 X 1 (1) 14 X 25 X 1 (1)
B - 17-1/2” 16 X 25 X 1 (1) 16 X 25 X 1 (1)
FIGURE 13 C - 21” 16 X 25 X 1 (1) 20 x 25 x 1 (1)
D - 24-1/2” 16 X 25 X 1 (2) 24 x 25 x 1 (1)
CAUTION
If this unit is being installed in a space serviced by an IMPORTANT
exhaust fan, power exhaust fan, or other device which If a high efficiency filter is being installed as part of this
may create a negative pressure in the space, take care system to ensure better indoor air quality, the filter must
when sizing the inlet air opening. The inlet air opening be properly sized. High efficiency filters have a higher
must be sized to accommodate the maximum volume static pressure drop than standard efficiency glass/foam
of exhausted air as well as the maximum volume of filters. If the pressure drop is too great, system capacity
combustion air required for all gas appliances serviced and performance may be reduced. The pressure drop
by this space. may also cause the limit to trip more frequently during
the winter and the indoor coil to freeze in the summer,
WARNING resulting in an increase in the number of service calls.
Our script found these filter sizes in the Lennox ML180UHE(K) source document's filter table: 14x25x1, 16x25x1, 20x25x1, 24x25x1. This page is pending human review, so check the source excerpt on the page to see which size applies to your cabinet and return. 14 X 25 X 1; 16 X 25 X 1; 20 x 25 x 1; 24 x 25 x 1.
General guidance (not from this manual): check monthly and replace 1-in. filters every 1–3 months, or follow the filter maker's guidance and your owner's manual.
Filter sizes are nominal (rounded). A filter sold as 16 x 25 x 1 actually measures about 15.5 x 24.5 x 0.75 in. Buy by the nominal size printed on the frame.
Manufacturer document for Lennox ML180UHE(K) (https://www.lennox.com/dA/ffe399214a/508541-01c.pdf), last checked 2026-10-23.