Home › Furnace filters › PG96VTA
The Payne PG96VTA furnace uses a 14 x 25 x 3/4, 16 x 25 x 3/4, 16 x 25 x 4-5/16, 20 x 25 x 3/4, 20 x 25 x 4-5/16, 24 x 25 x 3/4 or 24 x 25 x 4-5/16 filter, depending on cabinet width (or model) and return location (per the Payne document cited on this page). The table below shows which size applies to each cabinet and return.
Verified from manufacturer doc Filter sizes hand-checked against the manufacturer document
Last checked against the manufacturer document:
| Row label in Table 6 (in.) | Filter size | Filter type |
|---|---|---|
| 14-3/16 | 14 x 25 x 3/4 | Washable or media |
| 16 | (1) 16 x 25 x 3/4 or (1) 16 x 25 x 4-5/16 | Washable or media |
| 21 | (1) 20 x 25 x 3/4 or (1) 20 x 25 x 4-5/16 | Washable or media |
| 24-1/2 | (1) 24 x 25 x 3/4 or (1) 24 x 25 x 4-5/16 | Washable or media |
Payne's Table 6 heads this column 'Filter cabinet height'. Filters with a side return may have a different size; measure the filter. Not all families have the 14-3/16 size.

General guidance (not from this manual): check monthly and replace 1-in. filters every 1–3 months, or follow the filter maker's guidance and your owner's manual.
Pull the old filter and read the size printed on its frame. Nominal sizes are rounded up: a 15.5 x 24.5 in. filter is sold as 16 x 25.
Your furnace manual lists the filter's dimensions, not its MERV rating. Higher-MERV filters restrict more air. Manufacturers such as Carrier recommend keeping the clean-filter pressure drop under 0.2 in. w.c. (ideally under 0.1). Lennox warns that an over-restrictive filter can trip the high limit in winter and freeze the coil in summer. If you want MERV 11–13, a 4-in. media cabinet is the usual route. Ask an HVAC tech to check static pressure. Nominal sizes are rounded: a filter labeled 16 x 25 x 1 actually measures about 15.5 x 24.5 x 0.75.
Installation Instructions IM-PG96VTAA-03, Table 6 – Air Filter Selection and Duct Sizing
Last checked 2026-10-26. Manufacturers revise documents. If your unit's label disagrees, trust the label.
The Payne PG96VTA furnace uses a 14 x 25 x 3/4, 16 x 25 x 3/4, 16 x 25 x 4-5/16, 20 x 25 x 3/4, 20 x 25 x 4-5/16, 24 x 25 x 3/4 or 24 x 25 x 4-5/16 filter, depending on cabinet width (or model) and return location (per the Payne document cited on this page). The table below shows which size applies to each cabinet and return. 14-3/16 – 14 x 25 x 3/4 – Washable or media; 16 – (1) 16 x 25 x 3/4 or (1) 16 x 25 x 4-5/16 – Washable or media; 21 – (1) 20 x 25 x 3/4 or (1) 20 x 25 x 4-5/16 – Washable or media; 24-1/2 – (1) 24 x 25 x 3/4 or (1) 24 x 25 x 4-5/16 – Washable or media.
General guidance (not from this manual): check monthly and replace 1-in. filters every 1–3 months, or follow the filter maker's guidance and your owner's manual.
Filter sizes are nominal (rounded). A filter sold as 16 x 25 x 1 actually measures about 15.5 x 24.5 x 0.75 in. Buy by the nominal size printed on the frame.
Filter size filter size by row label in table 6 (in.): 14-3/16: 14 x 25 x 3/4; 16: (1) 16 x 25 x 3/4 or (1) 16 x 25 x 4-5/16; 21: (1) 20 x 25 x 3/4 or (1) 20 x 25 x 4-5/16; 24-1/2: (1) 24 x 25 x 3/4 or (1) 24 x 25 x 4-5/16 (per the source table).
Filter type filter size by row label in table 6 (in.): 14-3/16: Washable or media; 16: Washable or media; 21: Washable or media; 24-1/2: Washable or media (per the source table).
Installation Instructions IM-PG96VTAA-03, Table 6 – Air Filter Selection and Duct Sizing (https://www.shareddocs.com/hvac/docs/1009/Public/04/IM-PG96VTAA-03.pdf), last checked 2026-10-26.