Home › Furnace filters › 800SA / 801SA
Bryant 800SA / 801SA filter sizes: 14 x 25 x 3/4, 16 x 25 x 3/4, 20 x 25 x 3/4 and 24 x 25 x 3/4, as listed in the Bryant source document's filter table. Which size fits depends on your cabinet and return. This page is pending human review, so check the source excerpt below.
Auto-extracted · review pending Filter sizes auto-extracted from the manufacturer document.
Last checked against the manufacturer document:
| Sizes found in the source table |
|---|
| 14 x 25 x 3/4 |
| 16 x 25 x 3/4 |
| 20 x 25 x 3/4 |
| 24 x 25 x 3/4 |
Extracted by script from the linked document. Read the excerpt to see which size applies to which cabinet or return.
General guidance (not from this manual): check monthly and replace 1-in. filters every 1–3 months, or follow the filter maker's guidance and your owner's manual.
Pull the old filter and read the size printed on its frame. Nominal sizes are rounded up: a 15.5 x 24.5 in. filter is sold as 16 x 25.
Your furnace manual lists the filter's dimensions, not its MERV rating. Higher-MERV filters restrict more air. Manufacturers such as Carrier recommend keeping the clean-filter pressure drop under 0.2 in. w.c. (ideally under 0.1). Lennox warns that an over-restrictive filter can trip the high limit in winter and freeze the coil in summer. If you want MERV 11–13, a 4-in. media cabinet is the usual route. Ask an HVAC tech to check static pressure. Nominal sizes are rounded: a filter labeled 16 x 25 x 1 actually measures about 15.5 x 24.5 x 0.75.
Manufacturer document for Bryant 800SA / 801SA
Last checked 2026-11-02. Manufacturers revise documents. If your unit's label disagrees, trust the label.
8. Turn on electrical supply to furnace. a. Disconnect power choke wires (if used) and ground wire
attached to blower housing.
Table 14 – Filter Size Information (In. / mm) b. Remove screws securing cutoff plate and remove cutoff plate
FURNACE FILTER SIZE (In. / mm) from housing.
CASING c. Loosen set screw holding blower wheel on motor shaft (160+/-20
WIDTH FILTER
in.-lb. when reassembling).
In. (mm) Side Return Bottom Return TYPE*
14-1/2 16 x 25 x 3/4 14 x 25 x 3/4
d. Remove bolts holding motor to blower housing and slide motor
Washable out of wheel (40+/-10 in.-lb. when reassembling).
(368) (406 x 635 x 19) (356 x 635 x 19)
17-1/2 16 X 25 X 3/4 16 X 25 X 3/4 e. Remove blower wheel from housing.
Washable
(445) (406 x 635 x 19) (406 x 635 x 19) f. Clean wheel and housing.
21 16 x 25 x 3/4 20 X 25 X 3/4 10. Reassemble motor and blower by reversing steps 9f through 11a,
Washable
(533) (406 x 635 x 19) (508 x 635 x 19) finishing with 9a. Be sure to reattach ground wire to the blower
24 16 x 25 x 3/4 24 X 25 X 3/4
Washable housing.
(610) (406 x 635 x 19) (610 x 635 x 19)
NOTE: Refer to Table 5 for motor speed lead relocation if leads were
*. Recommended
Bryant 800SA / 801SA filter sizes: 14 x 25 x 3/4, 16 x 25 x 3/4, 20 x 25 x 3/4 and 24 x 25 x 3/4, as listed in the Bryant source document's filter table. Which size fits depends on your cabinet and return. This page is pending human review, so check the source excerpt below. 14 x 25 x 3/4; 16 x 25 x 3/4; 20 x 25 x 3/4; 24 x 25 x 3/4.
General guidance (not from this manual): check monthly and replace 1-in. filters every 1–3 months, or follow the filter maker's guidance and your owner's manual.
Filter sizes are nominal (rounded). A filter sold as 16 x 25 x 1 actually measures about 15.5 x 24.5 x 0.75 in. Buy by the nominal size printed on the frame.
Every size found in the source table is 3/4 in. thick: 14 x 25 x 3/4, 16 x 25 x 3/4, 20 x 25 x 3/4 and 24 x 25 x 3/4. Pending human review; check the excerpt.
Manufacturer document for Bryant 800SA / 801SA (https://www.shareddocs.com/hvac/docs/1009/Public/0F/II800SA-05.pdf), last checked 2026-11-02.